Showing all 42 results

CNC suction cup foam gasket replacement seal

3,60 5,00  Net of VAT

The price and quantity of the product are stated per meter, meaning that the stated cost and amount apply to one meter of the product

Engraving CNC Suction Cups

248,10  Net of VAT
Engraving CNC Suction Cups These are special very low suction cups to use on CNC routers for engravings low relief

Rectangular CNC vacuum pod 250×500 mm (9.84×19.68″)

405,60  Net of VAT
250 x 500 mm (9.8 x 19.6 inch) rectangular suction cup (also called vacuum pods or vacuum cups) This is

Rectangular CNC vacuum cup 100×500 mm (3.94×19.68″)

248,10  Net of VAT
Rectangular suction cup 100 x 500 mm (3 15/16 x  19 11/16 inches (also called vacuum pods or vacuum cups) Suction cup

Rectangular CNC vacuum cup 50×200 mm (1.97×7.87″)

165,40  Net of VAT
50 x 200 mm (1 31/32 x 7 7/8 inch) rectangular suction cup Suction-cup features: Hand-assembled Made of Anodized aluminum High-grip hot-vulcanized

Rectangular CNC suction cup 40×400 mm (1.57×15.75″)

190,60  Net of VAT
40 x 400 mm (1.57 x 15.75 inch) rectangular suction cup manufactured Suction-cup features: Hand-assembled Made of Anodized aluminum High-grip

Round CNC suction cup Ø65 mm (2.56″)

91,40  Net of VAT
65-mm (2.56 inch) diameter round CNC suction cup (also known as vacuum pods or vacuum cups) 65-mm diameter round suction

Suction cup for CNC Router – Special H=30 mm

202,50 337,50  Net of VAT
GNC Suction Cup for “small CNC Router” with special height of 30 mm This suction cup is used to hold

Vacuum manifold – GNC

231,60 637,10  Net of VAT
Aluminum vacuum manifold An aluminum vacuum manifold is a device that is used to connect a vacuum pump to suction

Top / bottom spare suction plate – GNC

24,00 211,35  Net of VAT
GNC – Top/bottom spare suction plate unit If you damage the vacuum plate (top or bottom) of your suction cup

Suction cup seal for CNC vacuum pods – GNC

1,75 41,80  Net of VAT
GNC – Suctiocup seal The suction cup seal is designed for use with double-vacuum suction cups, and it can

Pneumatic swing clamp stroke 40 mm

413,50  Net of VAT
Pneumatic swing clamp with stroke 40 mm for CNC working centers Mechanical clamp systems are real clamping plates. They are

Mechanical clamp – stroke 40 mm

165,40  Net of VAT
Mechanical clamp – stroke 40 mm Mechanical clamp for CNC working center. These clamps have a stroke of 40mm and

Suction cup retractable Ø200mm stroke 60 mm

413,50  Net of VAT
Suction cup retractable Ø200mm stroke 60 mm Thanks to the management of compressed air (in-out), this retractable suction cups cup

Pneumatic Pin-Stop Locator / backstop for CNC

248,10  Net of VAT
Pneumatic Pin-Stop Locator for CNC A Pneumatic Pin-Stop Locator, also known as a backstop, is a device that is used

Suction cup manifold 200×200 mm

248,10  Net of VAT
Suction cup manifold 200×200 mm The manifold suction cup encloses the advantages of a manifold distributor and a suction cup.

Pneumatic mushroom clamp stroke 60 mm

347,30  Net of VAT
Pneumatic mushroom clamp with 60 mm stroke Pneumatic clamp with piston 30mm diameter (the ring is 50mm). If you ed

Rollaway back stop stroke 48 mm

248,10  Net of VAT
Rollaway back stop stroke 48 mm Rollaway back stop are real automatic centering plates.  They are made of anodized aluminum

Breton locating device (flip stop)

124,50  Net of VAT
Locating device (flip stop) for Breton CNC If your Breton CNC is equipped with a slatted worktable you cannot use

Manual CNC pin stop locator

91,40  Net of VAT
Manual CNC Pin Stop Locators to easily locate your parts The manual location devices are used to place the workpieces

L Shape CNC vacuum pod 200x50x200 mm (7.87×1.97×7.87″)

248,10  Net of VAT
200 x 50 x 200 mm Corner suction cups (also known as vacuum pods or vacuum cups) Suction-cup features: Hand-assembled

L Shape CNC suction cup 150x35x150 mm (5.91×1.38×5.91″)

223,70  Net of VAT
150 x 35 x 150 mm corner suction cups (also known as Vacuum pods or Vacuum cups) Suction-cup features: Hand-assembled

Rectangular CNC vacuum pod 200×400 mm (7.87×15.75″)

289,80  Net of VAT
200 x 400 mm (7.87 x 15.74 inch) rectangular suction cup Suction-cup features: Modular system Hand-assembled Made of Anodized aluminum

Rectangular CNC vacuum pod 200×300 mm (7.87×11.81″)

248,10  Net of VAT
200 x 300 mm (7.87 x 11.81 inch) rectangular suction cup Suction-cup features: Hand-assembled Made of Anodized aluminum High-grip hot-vulcanized

Rectangular CNC vacuum pod 150×300 mm (5.91×11.81″)

207,20  Net of VAT
150 x 300 mm (5.91 x 11.81 inch) rectangular suction cup Suction-cup features: Hand-assembled Anodized aluminum High-grip hot-vulcanized rubber pads

Rectangular CNC vacuum pod 100×300 mm (3.94×11.81″)

190,60  Net of VAT
100 x 300 mm (3.94 x 11.81 inch) rectangular suction cup Suction-cup features: Made of Anodized aluminum High-grip hot-vulcanized rubber

Rectangular CNC vacuum cup 100×200 mm (3.94×7.87″)

157,50  Net of VAT
100 x 200 mm (3.94 x 7.87 inch) rectangular suction cup manufactured for CNC machines (also known as vacuum pods

Rectangular CNC vacuum cup 50×300 mm (1.97×11.81″)

174,10  Net of VAT
50 x 300 mm (1.97 x 11.81 inch) rectangular suction cup manufactured (also called vacuum pods or vacuum cups) Suction-cup

Rectangular CNC vacuum cup 70×240 mm (2.76×9.45″)

182,00  Net of VAT
70 x 240 mm (2.76 x 9.45 inch) rectangular suction cup manufactured (also called vacuum pods or vacuum cups) Suction-cup

Rectangular CNC suction cup 70×150 mm (2.76×5.91″)

165,40  Net of VAT
70 x 150 mm (2.76 x 5.91 inch) rectangular suction cup (also known as vacuum cups or vacuum pods) manufactured

Rectangular CNC suction cup 40×200 mm (1.57×7.87″)

157,50  Net of VAT
40 x 200 mm (1.58 x 7.87 inch) rectangular suction cup manufactured (also known as vacuum pods or vacuum cups)

Rectangular CNC suction cup 40×150 mm (1.57×5.91″)

141,00  Net of VAT
40 x 150 mm (1.57 x 5.91 inch) rectangular suction cup (also know as vacuum pod or vacuum cup) Suction-cup

Rectangular CNC suction cup 40×100 mm (1.57×3.94″)

124,50  Net of VAT
40 x 100 mm (1.58 x 3.94 inch) rectangular suction cup manufactured by (also known as vacuum pods or vacuum

Square CNC vacuum pod 200×200 mm (7.87×7.87″)

190,60  Net of VAT
200 x 200 mm (7.87 x 7.87 inch) square suction cup (also known as vacuum pad or vacuum cup) Suction-cup

Square CNC vacuum cup 150×150 mm (5.91×5.91″)

148,90  Net of VAT
150 x 150 mm (5.90 x 5.90 inch) square suction cup (also known as vacuum pad or vacuum cup) Square

Square CNC suction cup 100×100 mm (3.94×3.94″)

124,50  Net of VAT
100 x 100 mm (3.93 x 3.93 inch) square suction cup (also known as vacuum pad or vacuum cup) Square

Round CNC vacuum pod Ø250 mm (9.84″)

190,60  Net of VAT
250-mm (9.84 inch) diameter round CNC suction cup manufactured (also known as vacuum pods or vacuum cups) 250-mm diameter round

Round CNC vacuum pod Ø200 mm (7.87″)

141,00  Net of VAT
200-mm (7.87 inch) diameter round CNC suction cup manufactured (also known as vacuum pods or vacuum cups) Round 200 mm

Round CNC vacuum cup Ø130 mm (5.12″)

115,80  Net of VAT
130-mm diameter (5.12 inch) round CNC suction cup manufactured (also known as vacuum pods or vacuum cups) Suction-cup features: Hand-assembled

Round CNC vacuum cup Ø150 mm (5.91″)

124,50  Net of VAT
150 mm (5.91 inch) diameter round CNC suction cup manufactured (also known as vacuum pods or vacuum cups) Round vacuum

Round CNC suction cup Ø110 mm (4.33″)

107,90  Net of VAT
110-mm (4.33 inch) diameter round CNC suction cup (also known as vacuum pods or vacuum cups) This is one of

Round CNC suction cup Ø80 mm (3.15″)

91,40  Net of VAT
80-mm (3.15 inch) diameter round CNC suction cup (also known as vacuum pods or vacuum cups) Round suction pod diameter

CNC Suction Cups and Vacuum Pods for CNCs, for stone and glass working machines


CNC suction cups, CNC vacuum cups, (or CNC vacuum pods) for stone and glass working machines

CNC Suction Cups (also called CNC Vacuum Cups or CNC Vacuum pods) serve to raise workpieces from the working surface and securely hold them. A suction-cup system allows you to raise slabs from the table in order to drill, cut, or machine the edges. In a CNC Fabrication center, vacuum pods are also used to quickly position and secure the slabs to be worked.
Another reason vacuum pods are used is to always accurately position the slab in the exact same position to eliminate unnecessary set-up operations each time.  Mechanical pin stop locators or pneumatic backstops facilitate this step.

The friction pads on the top surface are made of hot-vulcanized rubber fused onto an anodized aluminum surface (designed to endure harsh and demanding industrial environments) guaranteed to not detach from the aluminum. The rubber friction-pad mixture is designed to ensure the best possible grip under any conditions and is contoured with specially-designed grooves to minimize the possibility of aquaplaning.
These CNC Vacuum Pods are specifically designed for work on marble, granite, glass, wood, and plastic materials.
The friction pad and the lip, or foam gasket, are made of stain-proof rubber, test-proven for use on white stone as well.

The columns have a special water-repellent, carbon-look coating that facilitates easy cleaning at the end of the day.

Our suction cups are rebored with a special tool before shipment to guarantee a height tolerance of  ± 0.02 mm.

Selecting the suction-cup model:

  1. Geometric shape: A suction cup’s most important differentiating feature is its shape, which may in fact vary from square, rectangular, round, or corner pieces.
  2. Height: The second distinguishing feature is height, which may be chosen from between 30 mm up to 240 mm.
  3. FabCenter brand: If you already have suction cups, when choosing your machine brand you can purchase suction cups, as a single kit, of the same height that you use in your current operations.

Customized CNC vacuum pods based on your needs:

  • Single-vacuum cups: these have just one vacuum on the top surface to hold the slab to be worked and are mechanically secured to the work table on the base.
  • Double-vacuum cups: these have a vacuum on both the top (to hold the workpiece) and the bottom (to secure the suction cup itself to the machine work surface).
  • Friction pad: the top of the suction cups may have an EDPM rubber lip or a foam-rubber gasket. The foam gasket is best suited for materials having irregular surfaces. Suction cups having a simple rubber lip are almost always used for glass.
  • Suction cup base: the base of double-vacuum suction cups may either be comprised of an O-ring gasket or EPDM rubber. EDPM rubber provides a stronger grip than the O-Ring gasket.
  •  Vacuum ports: finally, it is possible to choose the vacuum fitting size, which may range from 6mm to 12mm.

Our products include CNC suction cups of various sizes and shapes providing the best solution for any stone- or glass-industry application.
Our CNC Vacuum Pods are made in Italy and selected from the leading CNC manufacturers: Intermac, Breton, Denver, Bimatech, Park Industries, Pavoni,  CMS-Brembana, Loeffler, Prussiani, Helios, Omag, Thibaut, D2 Technology, Cobalm, Donatoni, Emmedue, and Northwood.

The surfaces of our CNC vacuum pods are designed to provide the best possible grip under all conditions and to avoid aquaplaning. They perform even when the material to be held is not perfectly planar – the case for natural stone. In the extruded rubber foam version – sealed on the sides – the gasket surface adjusts its contour to fit perfectly to the surface, precluding any loss of vacuum.
Buy your suction cups online at the best prices available on the market and customize them choosing the most suitable geometric shape,  your machine brand, the pod/cup heights for the single/double vacuum model, the pad seals, and other features.

Note: CNC Suction Cups, with heights between 30 mm to 49 mm are considered special cups, being particularly short. Customized cups may require a few more days to manufacture.
Upon request, you can also order cups taller than 240 mm or “specially customized cups”.
Please contact us at  should you have any questions

Read more: CNC Vacuum Pods – 4 common problems and how GNC resolves them